Skip to main content Skip to footer

Metal Roofing & Interior Conditions

May 15, 2004

May 2004 Interface • 29
As metal roofing becomes more commonplace, it is being
called upon to protect different interior environments.
These environments include offices, classrooms, and manufacturing
facilities, to name a few. As expected, the requirements
of each environment can vary greatly.
One component that should be addressed very early in the planning
stage is the interior relative humidly (RH) of the occupied
space. Higher interior humidity may require the use of different
materials or construction techniques. Geographic location can also
be a factor. Designs that work well in southern climates may not
give the desired performance when constructed in northern climates.
It may be difficult to locate a specific manufacturer’s
recommendations for design based upon interior conditions.
However, one manufacturer’s design manual contains
suggested guidelines for various interior humidity
levels. Page 70-01.7 of the Butler Roof Systems
Design/Specifiers Manual offers the following:
“The standard application of the MR-24 roof system
using faced blanket insulation meets most
building end use requirements where the interior
relative humidity (RH) is 30% or less. Building
interiors requiring 30% to 50% RH require blanket
insulation with a quality foil facing for specific
vapor control, special attention to insulation application
at joints and roof-to-wall transitions, and
provisions for adequate air movement. Building
interiors with RH requirements of 50% or greater
require a mechanical engineer’s approval of the
insulation system planned in conjunction with
adequate vapor control and air movement.”
So here we have one manufacturer’s basic guidelines to follow
for three distinct humidity ranges. These ranges are:
• Less than or equal to 30%
• 30% to 50%
• Greater than 50%.
Note these recommendations do not include a corresponding
interior temperature. A volume of air at 70% RH behaves very differently
at 0˚F, 70˚F, and 100˚F. If the RH of the same volume of air
is constant, the vapor pressure will increase as the temperature
increases. This raises another important point: interior tempera-
Photo 1: Moisture seeping through corrosion in roof panel.
30 • Interface May 2004
ture is also a major consideration of moisture control. If
there is a higher than normal interior temperature
(>75˚F), it may be prudent to consult with a mechanical
engineer regardless of the anticipated relative humidity.
For this article, we’ll assume that the manufacturer has
set these ranges based upon an interior temperature of
70˚F.
So the next question is, what relative humidity can we
expect to encounter? To paraphrase, ASHRAE Standard
55 suggests that the comfort range for relative humidity is
between 40% and 60%. These values are clearly above the
30% maximum previously stated for “standard applications”
and extend into the >50% range at which a
mechanical engineer should be consulted. Therefore, it
seems prudent that within “normal” office environments
(40% to 60% RH and 65˚F to 75˚F), one should always
consult with the manufacturer, and possibly with a
mechanical engineer, when designing a metal roofing system.
Topics of discussion should include insulation, vapor
retarder, detailing, and ventilation requirements.
How important is it to follow these recommendations?
Each situation must be considered upon its own merits,
but two examples are offered. The first involves a project
located in Iowa with a standing seam roof installed with
standard insulation, vapor retarder, and detailing (no special
provisions for high humidity). The roofing system was
seven years old and suffering from corrosion of the metal
roof panels.
One could actually walk across the roof and see water
seep out of the roofing system. Corrosion had penetrated
the panel, and moisture was released by the saturated
insulation when it was compressed by foot traffic ( see
Photo 1).
Inside, virtually all of the roof insulation blankets
were discolored and sagging. In several instances, condensation
could be viewed on the surface of the vapor
retarder (Photo 2).
It was also interesting to view the damage that had
occurred at a beam clamp. The clamp had been used to
support a sprinkler
line and was
installed on the top
chord of a truss. The
head of the clamp
had penetrated the
vapor retarder and
was in contact with
the underside of the
metal roof panel
(Photo 3). The clamp,
threaded rod, and
deck panel were all
badly corroded at
this point.
This roofing system
had clearly suffered
significant
damage. Our investigation
revealed high
Photo 2: Condensation forming on insulation facer.
Above: Photo 3: Deterioration of
beam clamp and underside of
roof panel.
Photo 4: Buckets suspended
from roof framing.
May 2004 Interface • 31
interior temperatures and humidity. Conditions recorded in the
damaged area ranged from 36% to 68% RH and temperatures from
67˚F to 81˚F. The worst case recorded was an interior temperature
of 75˚F, RH of 62%, with a resulting dew point of 61˚F.
In keeping with the previously listed recommendations, the
manufacturer and a mechanical engineer should have been consulted
during the design process. A few extra dollars spent up front
could have saved the owner the frustration and expense of a costly
and premature repair.
The second example involves a manufacturing facility, also
located in Iowa. The parent company had several operating plants
located in the South, all based upon a standardized, pre-engineered
metal building design. When the Iowa plant was completed
and placed into operation, nuisance leaks were reported throughout
the plant, primarily during periods of cold weather.
When we viewed the interior of the building, we found that a
large portion of the insulation blanket was wet, sagging from position,
and dripping water where it had been punctured. As the blanket
insulation became wet and sagged, the owner periodically
punctured the “low point” of the blanket to allow water to escape
in an effort to prevent the blanket from becoming dislodged and
falling.
As we walked through the plant, we noted that buckets had
been suspended from the roof trusses. These had been placed in
strategic locations to prevent water from dripping onto sensitive
equipment (Photo 4).
The sidelaps of the blanket insulation were found to have gaps
and were not taped or sealed together (Photo 5). We also found that
the blanket insulation had not been sealed around projections
(Photo 6).
When the client was asked about the building’s interior conditions,
he stated that the ideal operating conditions for the plant
were 70˚F and 42% RH. On-site measurements revealed that the
interior temperature ranged from 70˚F to 80˚F, and the RH varied
from 40% to 50%. These ranges were within the client’s acceptable
operating limits.
Photo 5: Insulation sidelap is “open” and not centered over framing
member. Page 31
Half Page Vertical
4-Color
Green Roofs for Healthy
Cities
New on disk
Remove this border.
32 • Interface May 2004
The client was dismayed when its previously successful design
(which worked fine in the South), failed to perform in a more northern
climate. This example points out another variable to be considered
– geographic location.
The National Roofing Contractors Association (NRCA) recommends
“that dew point related problems be considered in the design
of the roofing when the outside mean January temperature is below
40˚F, and/or the expected interior relative humidity is 45 percent
or greater.”
Had the designers heeded (or been aware of) the guidelines listed
above, they may have been able to prevent this unpleasant surprise.
As a result, the owner was faced with an expensive repair
that could have been avoided. As is often the case, the cost to make
repairs after the fact is much greater than if these enhancements
were incorporated into the original construction.
In summary, we should all be aware that the interior temperature,
relative humidity requirements, and the project’s geographic
location can have a dramatic effect on the proper design of a roof. ■
Photo 6: Insulation facer is not sealed around projection through
roof.
Frank Kelm is a project manager for
the Howard R. Green Company,
located in Cedar Rapids, Iowa, and
works primarily with building exteriors.
He has more than thirty years’
experience in the roofing industry,
and is a Registered Roof Consultant
(RRC) with the Roof Consultants
Institute.
ABOUT THE AUTHOR
E. FRANK KELM, RRC